Mercedes Coding Guide Book Vediamo-DTS Monaco

Mercedes coding By Vediamo-DTS Monaco Engineer System Training Books is a special set of manuals for Mercedes-Benz technicians who are struggling at a time when SCN online is still blocked but you have too much work that requires coding and programming such as Coding VGS, Program FBS…

That’s why I wrote this book to help technicians who want to repair Mercedes-Benz around the world can use the solution with a scientific sequence from easy to difficult as the table of contents below.

Vediamo Mercedes coding: Includes 28 parts

1. Engiener main interface
2. Connect with the vehicle
3. Connection protocol selection
4. Main button function description
5. Connection module submenu description
6. Read and save module information
7. Fault reading and quick clearing
8. Code saving
9. Control unit change code
10. Control unit SAM data write
11. Control unit programming
12. Change transmission coding
13. Installation of CLA/GLA/A/B
14. Vediamo open GLA200 156AUX
15. 166 Maintenance mileage change 10000KM
16. Cancel Installed engine, max. speed limit ME97
17. Refit 222 original factory memory seat
18. Personalization starts and stops Recall
19. Brush 213,238 and stop memory
20. Brush HU5S1 Harman audio
21. Add W205 Digital tire pressure
22. Add 176 digital tire pressure
23. Retrofitting W222 P20 Driver assistance system
24. Retrofitting 205 222 huds (IC222)
25. Cancel fuel evaporative emission system
26. 212 cancel the anti-collision aid system A90
27. GLE Gauge radio frequency
28. additional battery fault solution for 221 meters.

2. How will this book help you?

These two books will teach you how to use DTS Monaco and Vediamo Mercedes coding software in the most detail.

2.1 DTS-Engineer from A-Z engineering system training

This book will guide you in detail on how to use DTS Monaco software: Connect with the vehicle, Connection protocol selection, Main button function description, Connection module submenu description, Read and save module information, Fault reading, and quick clearing,…

DTS Monaco book Special Feature:

1. Quick Test: Entire vehicle ECU quick test, and the test can choose to edit more
2.  Variant Coding: Coding with variation add VO- delete VO function
3.  ID identification: One click to read the whole car and save all modules programmed numbers
4. Complete Variant Coding: One time to read all the ECU coding vehicle data, can be written to the vehicle again, completely off-line operation
5. Diagnostic Services: Advanced features can see your choice of internal and external data module, turn on the computer authorization(not driving license), Activate ECU, reset ECU, modifying the original chassis number
6. Flash programming: Fully offline programming
7. Diagnostic Trouble Code: Diagnostic module DTC fault code
8. ECU Exchange: Two of the same ECU, by reading data import data exchange
9. Symbolic trace: Record and track the file, after repeated viewing, analysis of fault logic point

  DTS-Monaco Software 

• DTS Monaco Mercedes software is a support software for new models from (2017- to the present) and is recommended by Daimler-Benz development engineers, as a general technical test terminal for functions. diagnostics and control of vehicle control unit…etc. The name Monaco is derived from the modular analyzer used in vehicular traffic, and tasks in the engineering field.

2.2 Vediamo Engineer System Training

This book will guide you on how to use Vediamo software in the most detail through illustrations: Code saving, Control unit change code, Control unit SAM data write, Control unit programming, Change transmission coding, Installation of CLA/GLA/A/B, Vediamo open GLA200 156AUX…

 Vediamo Software 

• Vediamo Software – Engineer software dedicated to programming and coding Mercedes-Benz old models (1999-2017) or distributed diagnostics applications for the engine (Verteilte Diagnose Anwendung für Motoren) – is an electronic control unit (ECU) diagnostic software system integrated into the CAESAR / DIOGENES process chain. It can test on any ECU over K-Line and CAN and includes all protocol settings from RTMD+, MBISO, KWFB, KW2000, to UDS.

Specialized diagnostic equipment that supports coding Mercedes Benz

• (Recommend) SD Connect C4 DOIP Connection Device is probably not too strange for technical staff in the automotive field. But not everyone can access and use it. To spend such a huge amount of money, not everyone is willing to invest and buy it. But for the SD Connect C4 doip REP 1:1 product, you only need to spend an amount equal to 1/100 of the genuine product but also own the basic features to ensure the process of your work.

Other devices

Devices that can connect and use engineer software are Openport 2.0, VAS5054, VCI C5, VCI C6, and M6 Pro for coding Mercedes -Benz. But we do not encourage our technicians to use them because, during work, the device is unstable, slow connection and interaction with software, and many errors in the process of adding files for coding and programming.

At a time when SCN online is blocked, I believe that the best solution for a technician is to learn how to use Vediamo/DTS-Monaco engineer software for your own Mercedes-Benz repair work. To get the best guidance and advice from experts with many years of experience in the field of Mercedes-Benz repair and maintenance.

Not only can you learn how to use the software through these books, but also watch our live video tutorials through this Youtube channel: Car Diagnostic Software

Here is an example video that you can refer to This is the process by which I used Vediamo software and professional diagnostic equipment SD connect C4 doip to coding-programing VGS-3 of Mercedes-Benz models.

If you have any problems when use Mercedes coding function, please contact me immediately for expert support :